企业招商网
总站
[切换城市]
免费发布信息
    您所在的位置: 总站首页 > 广东企业招商网 > 佛山企业招商网 > 供应信息 > 电工、电气 > 电动机

供应17AM保护器

供应17AM保护器
品牌17AM型号17AM温控范围60-150(℃)工作电流8(A)工作电压250(V)产品认证UL 1. 产品用途 Product use17AM-D 系列热保护器是一种具有对温度和电流双重感应特性的产品,该产品结构先进、体积小、动作灵敏、触点容量大、寿命长的特点,广泛适用于分马力电机、电热器具、荧光灯镇流器、变压器、汽车马达、集成电路及一般电气设备的过热、过电流保护。17AM-D series thermal protector is the product that is sensitive to temperature & current.It is of advanced structure 、small volume 、sensitive in action 、big contact capacity & long life. It protects against overheating & over-current in motor 、electric & thermal appliance 、lamp ballasts 、transformers、automotive motor 、integrated circuit & common electric equipment.2. 结构 Structure2.1 外观:外形尺寸符合产品图纸要求(见附图)Appearance:Dimension is complied with the draw.(Refer to draw)2.2 导线:UL3321、AWG #18镀锡铜芯线、黑色Leads:UL 3321 or AWG #18 copper core leads, black color, tinned2.3 外壳:表面镀镍锌合金的板材Case:The steel material used for case is plated with alloy of nickel and zinc2.4 套管材料:聚脂绝缘套管符合电器用品的性能要求。Sleeve material:Insulated sleeve is complied with electric appliance’s requirement.3. 性能(Capability)3.1 额定电流 Rating current20A/115V、8A/AC250V3.2 抗拉力试验:产品的接线端子应能承受大于或等于50N拉力,铆接处不应松脱,导线无断裂、滑出。Pull trial :Terminals should endure more than 50N. And terminals should be no loose and leads have no rupture and slipping。3.3 绝缘电压 Insulated voltageA. 热保护器在热分断后的接线之间应能承受AC660V,历时1min而无击穿闪络现象;The leads should endure AC660V after opening without arc over under duration of 1min.B. 热保护器端子引线与绝缘套管之间能承受AC1500V,历时1min而无击穿闪络现象;The outgoing lines or terminals of the thermal protector and insulated sleeves shall endure voltage of 1500V and duration of 1min, without arc over.3.4 绝缘电阻:在正常条件下,导线与绝缘套管之间的绝缘电阻在100MΩ以上。(所用表计为DC500V绝缘抵抗计)Insulated resistance:Under normal conditions ,insulated resistance between leads and insulated sleeve should be more than 100MΩ.(By insulation measurement machine)3.5 接触电阻:热保护器的接触电阻应不大于50mΩ。Contact resistance:Contact resistance of thermal protector should be less than 50mΩ.3.6 气密性试验:保护器在大于85℃的水中(水不沸腾),应无连续的气泡冒出。Seal trial :There is no continuous air bubble from the thermal protector, if the protector is placed in 85 deg. Water (not boiling water)3.7 耐热试验:产品在150℃的环境中放置96 小时。Hot endure trial:It will last 96 hours if the protector is placed where the ambient temperature is 150 deg.3.8 耐湿试验:产品在40℃、相对湿度95%的环境中放置48 小时。Damp endure trial :It will last 48 hours if the protector is placed where the ambient temperature is 40 deg. and relative humidity is 95%.3.9 热冲击试验:产品在150℃,-20℃环境中交变放置各30min,共5 个周期。Hot affect trial :It will last 5 cycles if the protector is placed where the ambient temperature is exchanged between 150 deg. and minus 20 deg. for 30min.3.10 耐抗振试验:产品能承受振幅1.5mm,频率变化10~55Hz,扫描变化周期为3~5min,振动方向X、Y、Z,每个方向连续振动2 小时。Vibration endure trial :The thermal protector should be normal after 2h in the conditions with amplitude of 1.55mm, frequency change of 10~55Hz, change period of 3~5 min, Vibration directions of X, Y and Z.3.11 跌落试验:产品自0.7m 高度自由落下1 次。Fallen trial:Let the thermal protector freely fall down 0.70m above cement ground.3.12 抗压性:将产品浸入密封油罐中,施加2MPa 的压力并保持24h 后.Press endure :Let the thermal protector immerge in the sealed oilcan and give 2MPa press lasting for 24 hours.3.13 第3.8,3.9,3.10,3.11,3.12,3.13 项试验后应满足下列条件:After 3.8,3.9,3.10,3.11,3.12,3.13 trial ,the performance of the thermal protector shall meet the following requirements:A. 动作温度变化应在初期值的±7℃以内;Change of opening temperature shall be within ±7℃ of the initial value.B. 接触电阻应在50mΩ以下;Contact resistance should be under 50mΩ.C. 外形应无明显变形;Appearance should not be evident distortion.D. 导线无开裂损伤;Leads should not be craze.E. 绝缘电压应符合3.4 项要求;Insulated voltage shall be complied with 3.4.F. 绝缘电阻应符合3.5 项要求。Insulated resistance shall be complied with 3.5.4. 寿命 Life产品在额定电压、电流、功率因数为0.7 的条件下,外加热源使其动作1000 次,应满足下面条件:The Protector acts 1000 under external power in the condition of rating voltage 、current and 0.7 power. the performance of the thermal protector shall meet the following requirements:A. 动作温度变化应在初始值的±7℃以内Change of opening temperature should be within ±7℃ of the initial value。B. 接触电阻应在100mΩ以下;再继续试验5000 次后其动作需正常无误。Contact resistance should be less than 100mΩ.The opening temperature shall be normal after going on 5000 circles.5. 其它事项 Additional items5.1 动作温度检测的升温速率应控制为1℃/1min;During the opening temperature trial, the rate of temperature rising should be controlled by 1℃/1min.5.2 使用过程中保护器外壳不能承受强烈冲击力及压迫力;The case of protector can’t endure strong strike and press when it is used in circuit5.3 认证:(License)UL 认证(UL File No.):E214731CQC 认证(CQC File No.):CQC04002009719VDE 认证(VDE File No.):400098506. 本标准未涉及事项或客户有其它要求另行订立。The items which this standard have not referred or customs require shall be madeadditionally.
(联系我时,请告知从企业招商网看到的信息,将获得最优质服务)
  • 【公 司】:广东省佛山市积辉电器有限公司
  • 【联系人】:李湖波先生
  • 【电 话】:
  • 【手 机】:
  • 【传 真】:
  • 【邮 箱】:
  • 【地 址】:中国广东佛山市佛山市南海区罗村镇桂丹路交警中队旁致豪包装二楼
赞助商链接
推荐信息
赞助商链接